s50 door access user menu control system programming code setting
Share
RFID Access Control System
User’s Manual
Please read this manual thoroughly before installation.
- Brief Product Introduction:
This product is RFID access control system, which is currently one of the advanced access systems. It uses the latest central process unit (CPU) and memory chip of large capacity. There will be of no information loss even in case of power failure. It takes the latest HOMMARD technology, with strong power of three ways to open door: open by card read, open by card read adding with password, and open by password.
This product provides access control mode, which is safe and fully automatic, it is an ideal device for business organizations, offices, factories, residences and communities.
- Technical Features
|
No. |
Item |
Specification |
|
1 |
Power supply |
DC: Voltage 12V±10%; current < 0.1A |
|
2 |
Max load |
Alarm output: 100mA Electrolock output: 5A |
|
3 |
Dimension |
118mm×78mm×25mm |
|
4 |
Weight |
130g |
|
5 |
Ambient temp. |
-20℃—60℃ |
|
6 |
RH |
20%—90% |
|
7 |
Memory capacity |
Information of 600 user card, and 1 passwords |
|
8 |
Induction distance |
5－15CM |
|
9 |
Car type |
EM or MF1 compatible card |
3、Status Indications:
LED Indicators
|
Status |
Red LED |
Green LED |
|
Normal state |
Flash |
|
|
Valid card |
|
Light |
|
Invalid card |
Light |
|
|
Open |
|
Light |
|
Key Press |
Light |
|
|
Program Mode |
Light |
Flash frequent |
|
Alarm |
Flash |
|
Buzzer
|
Status |
Description |
Buzz |
|
Valid card |
Two short beeps |
BiBi |
|
Invalid card |
Long beep once |
Bi—— |
|
Key Press |
Short beep once |
Bi |
|
Input valid password |
Two short beeps |
BiBi |
|
Input wrong password |
Long beep once |
Bi—— |
|
Alarm state |
Continuous long beeps |
Bi—Bi—Bi— |
- Setup:
- Default value: Login password 1234
- Enter programming mode:
Press * Login password # enter programming mode.
- Function setup (should be in programming mode):
1). Modify login password.
Press * Login password # 0 new password # confirm new password # *
Note: the new password should be any 4-6 figures.
2). Add user card.
Press * Login password # 1 read card Input code # *
Note: the code should be three figures from 001 to 600, which should not duplicate. The code must be input, otherwise the card will be invalid. If add more than one cards, read the second card directly after the first three-digit code is put in before pressing # .
3). Delete user card (three ways):
- Press * Login password # 2 0 0 0 0 # * to delete all user cards.
- Press * Login password # 2 read card # * to delete the corresponding card
- Press * Login password # 2 input code # * to delete lost card.
4) Set open mode:
Press * Login password # 3 0 0 # * by valid card only.
Press * Login password # 3 0 1 # * by valid card and password.
Press * Login password # 3 0 2 # * by valid card or password.
Note: factory setting is valid card.
Since the initial password can not be used to open door, If set to valid card or password mode, password for use should be modified.
5). Set the length of open time:
Press * Login password # 4 X X # * .
Note: XX is from 00-99, unit is second, factory setting is 6 seconds.
6). Set open door password:
Press * Login password # 5 open password # open password # *
Note: password length should be 4-6 figures.
- How to use:
1). In normal work mode, can be open by one valid card.
2). When valid card and password mode, can be open if the correct password is put in within 10 seconds after card swiping.
3). If the password of a card is forgotten, the information of this card in the system should be deleted first, then add this card to the system again to modify the password.
4). If program password is forgotten, you can use jumper switch“RESET”at the main board to restore factory setting. First, power off. Then set jumper switch to“ON”position. Power on. Shift the jumper switch back to “OFF”position after three beeps of the buzzer, now the factory setting is restored.
Attachment: wiring diagram for installation
|
1 |
Red |
12V |
(+)12Vdc Positive Regulated Power Input |
|
2 |
Black |
GND |
(—)Negative Regulated Power Input Door Strike Relay COM |
|
3 |
Yellow |
NC |
Door Strike Relay NC |
|
4 |
Green |
NO |
Door Strike Relay NO |
|
5 |
Blue |
OPEN |
To Door Remote Control Button Then Negative |
|
6 |
Blue |
OPEN |
To Door Remote Control Button Then Negative |
|
7 |
White |
BELL |
Bell Push Button |
|
8 |
White |
BELL |
Bell Push Button |
NOTE: 1. Power off before installation wiring,
hot line work is forbidden!!
- Normally, electrolock is connected out
from power controller.
Auxiliary Function：
1.External RFID Reader (Support Door opening by pass word)
|
RED |
+12V |
|
Blank |
GND |
|
Green |
DATA 0 |
|
White |
DATA 1 |
|
Bule |
BUZZER LED |
2.Relay Output ( Remove the cap from the Three Pin Jumper)
|
White |
NO |
|
Blue |
COM |
|
Yellow |
NC |
- If you set it to value 99, it will change to Card Open and Card Close operation.